Dynaverse.net
Taldrenites => Starfleet Command Models => Topic started by: Arcanum on June 28, 2005, 01:19:09 pm
-
Hey all,
Been thinking about this ship for awhile but . . I don't have the ability to mod or kitbash so hopefully I can interest a modder in this one!
Basic discription of parts ;D
Saucer: Excelsior class style
Neck: TMP Constitution class with 1 rear ward torpedo port
Hull: Ambasador class minus the lip around the rear/shuttle bay
Engine Pylons: TMP Constitution class, mount Constitution style
Engines: Excelsior class.
I think she would be a sweet looking ship myself, what do you think?
-
It sounds somewhat similar to the Lexington class. It might be interesting to play around with that.
-
Check Starship Schematic's webpage IIRC I've seen one like the one you've just described.
-
Hey all,
Been thinking about this ship for awhile but . . I don't have the ability to mod or kitbash so hopefully I can interest a modder in this one!
Basic discription of parts ;D
Saucer: Excelsior class style
Neck: TMP Constitution class with 1 rear ward torpedo port
Hull: Ambasador class minus the lip around the rear/shuttle bay
Engine Pylons: TMP Constitution class, mount Constitution style
Engines: Excelsior class.
I think she would be a sweet looking ship myself, what do you think?
There'd be a bit of a scaling issue with the engines and saucer coming from an Excelsior and the rest primarily from a Connie... I iimagine that yu'd be scaling closer to Excelsior size than Connie?
I have all the basic parts, so I could probably do this... just hoping to get some more details on what you were looking for..
-
Mr Tricorder Models Please: ;)
Thanks I had to go look that one up, yes something like Mackies USS Ironcross is the one made in that style, which uses a stretched Connie style lower hull. This is the one you meant too MP?
http://www.the-tcs.net/ships/images/ironcross.jpg
Atheorhaven: 8)
Yes the size would be approximately on scale with an Excelsior, given the saucer and the engines with the larger Ambasador secondary hull. I took another at look at the USS Banting that Constitution variant with Excelsior engines she also has TMP Connie style engine pylons. The Ambasador secondary hull might need a rescaling but I am not sure, the Excelsior saucer/engines should be OK.
The idea for a Connie "neck" was some newer style ships (Excelsiors etc) have a large thick style neck and are abit less graceful there (short and wide) that and I like the forward torpedo bay on the TMP Connies :D. Rear torpedo tube on the neck ala TNG.
Frontal profile would be like a Constitution, classic Fed with the engins just showing above the saucer.
I was thinking of this ship in terms of the ship between the Excelsiors and the Ambasadors. A late TMP cross over to Lost Years Era, I thought she would be a heavy cruiser/battlecruiser.
Thx!
-
Bantings Excelsior Style warp engines are scaled down. Reason being is that the Physical model uses the the amt model parts to make her up. ;D Thanks for looking at her for reference ;D
-
The Lexington actually looks roughly like this: http://www.universeatwar.org/drs/downloads/fed/lexington_angle1.jpg
That model is a fairly accurate recreation of the original Lexington from Klingon Academy, it's a midway between the Connie and the Excelsior though, not the Lost Era ship you want to make.
No offence intended Arcanum but I don't think mishmashing all those different parts together is going to look very good, there are a few designs on the net that bridge the Excelsior -> Ambassador gap very nicely but they are all new builds rather than kitbashes that meld features from both ships into a consitent design rather than just sticking the different bits together. Obviously it's your project and whatever you think is good is what you should make, that's the reason we're all here, just throwing in my €0.02.
-
It really all depends on the texturing. It may not be a good representation of a lost era ship, but it would be an interesting design. If you can give it a good paint job, you might not look quite so kitbash-esque may actually be a pretty cool design. Just my $0.02 (which unfortunately isn't worth as much as S33K100's €0.02).
-
The benefits of a (relatively) stable economy I guess. Seriously though yes textures will make a big difference, if you pick a style, probably that of the Excelsior for your ship, and make new textures for the Ambassador and Connie-R parts to match up it can mask their presence quite well, can't think of any examples right now, though I've had to do that to some parts I've used in some kitbashes of mine in the past.
-
My Mark 6 Connie ships have a rear firing torpedo launcher on the back of the neck. I borrowed the idea from WZ's Lethality model. Ask WZ if he'll allow the parts to be used.